Minimoog Voyager XL
Moog Music is incredibly honored that The Minimoog Voyager XL was voted Best Keyboard/Synthesizer by the readers of Sound On Sound magazine.
Incorporating virtually all of the sound resources and functions of the original Minimoog Model D and Voyager, The Minimoog Voyager XL features extensive front-panel patchability that harkens back to the original ground-breaking Moog modular synthesizers. A host of features previously found only on massive modular synthesizers combined with state-of-the-art analog technology make it a sound design and control dream machine. Highlights include:
61-Note Velocity Sensitive Keyboard with After-Pressure
Ribbon Controller with Pitch and Gate CV Outputs
Touch Surface Controller with X, Y, A and Gate Outputs
External Audio Input
Effects Loop Insert
2 Active Attenuators
4-Input CV Mixer
Additional LFO Source with Multiple MIDI-Syncable Waveforms
3 Four-Way Mults
20 Control Voltage Outputs
3 Gate Outputs
10 Control Voltage Inputs
4 Gate Inputs
2 Modulation Busses
Solid Maple Cabinet
Tilting Control Panel
Minimoog Voyager XL
100% Analog Sound Engine
The MINIMOOG VOYAGER XL Synthesizer is a monophonic analog performance and production synthesizer. Based on the Minimoog Voyager sound engine, it incorporates virtually all of the sound resources and functions of the original Minimoog Model D and Voyager, with the addition of a number of exciting features from Moog's modular synthesizer legacy.
61-Note Velocity Sensitive Keyboard with after-pressure. Identical to the Voyager 44-note keyboard.
A 500mm Ribbon Controller is located on the middle wooden rail of the Voyager XL. It's center-point is lined up with 'middle-C' of the 61-note Keyboard. Outputs are sampled and available as CV-OUT (-5V to +5V) and GATE-OUT (0V to +5V).
(20) Control Voltage output
- Keyboard Pitch (w/ internal trim to calibrate to 1 V/Octave)
- Keyboard Velocity
- Keyboard Afterpressure
- Touch Surface X
- Touch Surface Y
- Touch Surface A (area)
- Pitch Bend Wheel
- Mod Wheel
- MOD 1 signal (signal at MOD 1 input)
- MOD 2 signal (signal at MOD 2 input)
- LFO triangle wave
- LFO square wave
- Mod Wheel Mod Buss output
- Pedal/On Mod Buss output
- Filter Envelope
- Volume envelope
- Sample and Hold Step
- Sample and Hold Smooth
- Ribbon Controller CV Output (-5V to +5V)
(3) Gate outputs
- Keyboard Gate
- Touch Surface Gate
- Ribbon Controller Gate Output
(3) 4-way Mults (top jack is ring-powered)
(10) Control Voltage Inputs
- Envelope Rate CV (-5V to +5V) Ring-Powered
- OSC Pitch CV (adj. to 1V/Octave) (-5V to +5V) Ring-Powered
- OSC Wave CV (all three osc. affected) ( 0V to +5V) Ring-Powered
- FILTER Cutoff CV (-5V to +5V) Ring-Powered
- VCA Volume CV ( 0V to +5V) Ring-Powered
- VCA Pan CV (-2.5V to +2.5V) Ring-Powered
- LFO Rate CV (-5V to +5V) Ring-Powered
- MOD Mod1 CV ( 0V to +5V) Ring-Powered
- MOD Mod2 CV ( 0V to +5V) Ring-Powered
- S&H CV (-5V to +5V) Ring-Powered
(4) Gate Inputs
- ENV Release ON/OFF (0V OFF, +5V ON)
- ENV Gate Input (0V OFF, +5V ON)
- LFO Sync ON/OFF (0V OFF, +5V ON)
- S&H Gate Input (0V OFF, +5V ON) No footswitch input
(2) Active Attenuators
Active Attenuators are identical to the VX-352 attenuators with the following difference:
CHANNEL 1 is normalled to LFO 2 output. So, if nothing is connected to the Channel 1 input jack, the output of Channel 1 will be the attenuated version of the LFO 2 output.
CHANNEL 2 is normalled to RIBBON output. So, if nothing is connected to the Channel 2 input jack, the output of Channel 2 will be the attenuated version of the RIBBON controller.
EXPRESSION PEDALS can be connected to the Attenuator inputs (i.e. they are ring-powered inputs).
AMOUNT controls gain of -1 (CCW) to 1 (CW). Thus, the attenuators can create an inverted version of the waveform.
OFFSET control allows you to add a DC voltage of -5V to +5V to the input signal. The Attenuator output will be clipped to approximately +/-10V.
- Inputs 1 and 2 can be attenuated via front-panel knobs
- Inputs 1 and 3 can be controlled by Expression Pedals (i.e. ring-powered)
- Two output CV's (+) and (-)
- DC offset can be added to signal via OFFSET knob
- Overall output of MIXER can be adjusted via the MASTER knob
RISE and FALL time constants are adjustable from 1 millisecond to 1 second (middle is 100 millisecond).
A MIDI-syncable second LFO source has been added to the Voyager XL. The default frequency range is 0.02Hz (50 seconds) to 20Hz (0.05 seconds). This range was made to augment the current Voyager LFO which does not go slow-enough for some very slow modulations.
INPUTS: LFO 2 can be
- Free-running (adjusted by the RATE knob on the front panel)
- MIDI SYNC from external MIDI clock
- Directly CLOCKED from a GATE CV via the front panel CLOCK jack
- Controlled via external CV or Expression Pedal via the front panel RATE CV jack
OUTPUTS: LFO 2 has two complementary LFO outputs labeled (+) and (-). In default mode, these are the same waveform 180 degrees out of phase.
Available front-panel waveforms:
- S&H SMOOTH
Power input accepts a standard power cable. The Minimoog Voyager XL works from 100-250 VAC, 50-60 Hz.
The TNC Lamp Socket provides 12VDC for a gooseneck lamp.
Equipment available to buy from this site is for professional use only. Please note in certain countries some products listed may not be available from A.C. Entertainment Technologies Ltd.
E&OE. Information is subject to change without notice. The rights and ownership of all trademarks are recognised.